SOLVENT
IMMEDIATELY REPLACES ACETONE
 |
AREAS OF USE
Cleaning rollers, de-icers and application tools for the implementation of polyester resins and epoxies.
NEUTRALENE RG 30 has an optimized evaporation rate allowing effective action even on highly reactive resins having a short TECAM gel time of a few minutes.
|
UPR RESINS Aliphatic Homopolymers PGA PLA PGL PCL PHA PHB Aliphatic co-polyesters PEA PBS Semi-aromatic co-polyesters FBT PTT PEN Homo and aromatic co-polyesters Polyacrylates Hybrid polyester polyesters - epoxies
|
|
EPOXY RESINS Epichlorohydrin ECH BPA Bisphenol Aliphatic Glycol Phenolic novolacs o-Cresols Hydantoins (urea glycols) Brominates, acrylates
|
|
EPOXY HARDENERS DDM MDA Polyisocyanates Aliphatic amines Base anhydrides TGIC (triglyceride isocyanates) |
NEUTRALENE RG 30 is an excellent diluent and cleaning agent for tools and paint application and rinsing equipment, including circulating solvent-based paints.
- Natural driers
- Cellulosics
- Rubber
- Vinyl
- Acrylic
- Polyester
- Phenolics (resoles)
- Aminoplasts
- Polycarbamides
- 2 K epoxides (2 components)
- 2 K polyurethanes (2 components)
A better alternative than more toxic blends
with Xylene - Toluene / MEK - MIBK
Use only with solvent based paints; do not use with water-based paints (Hydro). Do not use as thinner (for viscosity) on epoxy and polyurethane systems.
ECONOMIC ASPECTS
Reduction of consumption
NEUTRALÈNE® RG 30 a has a vapour pressure of 1.2 kPa at 68°F.
Acetone has a vapour pressure of 24.7 kPa at 68°F, over 20 times greater than that of NEUTRALÈNE RG 30. Consequently, it is easy to deduce from this that there would be a considerable reduction of solvent consumption – by about 5 times – avoiding any unnecessary loss by evaporation. It is well known that acetone often requires multiple applications in succession due to its almost instantaneous evaporation rate.
Recyclable, reusable
NEUTRALENE® RG 30 is an azeotrope, its distillation point is 257°F.
It is easy to recover, distil and reuse, with no loss of its physico-chemical qualities.
The distillation point can be lowered by approximately 30% if a vacuum distiller is used. Distillation is then total and extremely rapid, at 194°F.
For post-production cleaning of tools by immersion, for cleaning equipment that is used to produce resins, or for cleaning tanks, valves, pumps etc.
PHYSICO-CHEMICAL CHARACTERISTICS
|
CHARACTERISTICS |
STANDARDS |
VALUES |
UNITS |
|
Aspect |
Visual |
Limpid |
- |
|
Colour |
Visual |
Colourless |
- |
|
Odour |
Olfactory |
Characteristics |
- |
|
Density at 77°F |
NF EN ISO 12185 |
889 |
kg/m3 |
|
Refractive index |
ISO 5661 |
1.3970 |
- |
|
Freezing point |
ISO 3016 |
-58 |
°F |
|
Boiling - Distillation |
ISO 3405 |
246.2-258.8 |
°F |
|
Vapour pressure 68°F |
ASTM D 5188
EN 13016.1.2.3 |
1,2 | kPa |
|
Solubility in water |
- |
0.01 |
% |
|
Kinematic viscosity at 104°F |
NF EN 3104 |
0.86 |
mm²/s |
|
Acid number |
EN 14104 |
<1 |
mg(KOH)/g |
|
Iodine index |
NF EN 14111 |
0 |
gI2/100g |
|
Water content |
NF ISO 6296 |
<0.1 |
% |
|
Residue after evaporation |
NF T 30-084 |
0 |
% |
|
PERFORMANCE CHARACTERISTICS |
|||
|
CHARACTERISTICS |
STANDARDS |
VALUES |
UNITS |
|
KB Index |
ASTM D 1133 |
>150 |
- |
|
Evaporation rate |
- |
4.30 |
minutes |
|
Surface tension at 68°F |
ISO 6295 |
27.5 |
Dyne/ cm |
|
Copper blade corrosion 100hrs at 104°F |
ISO 2160 |
1a |
Rating |
|
FIRE SAFETY CHARACTERISTICS |
|||
|
CHARACTERISTICS |
STANDARDS |
VALUES |
UNITS |
|
Flash point (closed cup) |
NF EN 22719 |
84.2 |
°F |
|
Self-ignition point |
ASTM E 659 |
>446 |
°F |
|
Lower explosive limit |
NF EN 1839 |
1,2 |
% (volume) |
|
Upper explosive limit |
NF EN 1839 |
13,7 |
% (volume) |
|
TOXICOLOGICAL CHARACTERISTICS |
|||
|
CHARACTERISTICS |
STANDARDS |
VALUES |
UNITS |
|
Content of CMR substances, irritating, corrosive |
CLP Regulation |
0 |
% |
|
Residual methanol content from transesterification |
GC-MS |
0 |
% |
|
ENVIRONMENTAL CHARACTERISTICS |
|||
|
CHARACTERISTICS |
STANDARDS |
VALUES |
UNITS |
|
Water hazard |
WGK in German |
1 not hazardous to water |
class |
|
Primary biodegradability CEC 21 days at 77°F |
L 33 T82 |
>70 |
% |
|
Ready biodegradability OECD 301 A in 28 days Disappearance of COD |
ISO 7827 |
>70 |
% |
|
Ready and ultimate biodegradability OECD 301 D in 28 days Biodegradation at 67 days |
MITI modified |
72 |
|
Precautions for use: Product classified as inflammable, below 145,4°F flashpoint. Product contains no raw material classified as CMR, toxic, noxious, irritating or sensitising. Refer to the safety data sheet. Thoroughly read the label on the package. In case of fragmentation, transfer this to the new packaging. Use pure, do not mix with water.
NEUTRALENE® RG 30 is a powerful solvent and dissolvent of resins; we advise doing a preliminary test when preparing surfaces on plastic or elastomer materials.
PRESENTATIONS
|
Drum 200 L
|
Can 20 L |
Can 5 L |
Looking for another product?
|
Discover our entire range by clicking on the photo |
Manufacturing, lubrification, cleansing, protection,
IBiotec® Tec Industries® Service
offers a wide range of products reserved for industrial area
If you wish for :
a free sample
a technical advice
a product data sheet
a safety data sheet
IBiotec® Tec Industries®Service
manufacturer of technical chemical products.
Welcome to our website.
IBiotec® Tec Industries®Service is on : 